Strength and versatility, Warne Maxima steel bases are the strongest and most versatile mounting system available today. The simple low profile design along with steel construction is a significant upgrade from any other 2 piece bases. The Maxima Steel Bases are modeled around the popular we'ver design, which is one of the strongest and most versatile mounting systems available today. The low profile of the Maxima Steel Bases give your firearm a sleek look. When used in conjunction with Warne Maxima QD Rings, the shooter is able to utilize the open sights by looking over the top of the bases without sacrificing the normal shooting position behind the firearm. Maxima Bases also offer a full width recoil slot in each base. This feature allows the recoil control keys of Warne Rings to attain maximum bearing surface.

Maxima scope bases from Warne Scope Mounts equip your Mauser FN model for successful targeting.

This two-piece M902/830 M Maxima scope base relies on premium steel construction to give you impressive strength and service with a low profile. These are some of the best two-piece mounts available on the market. These bases are ideal for use with Maxima QD scope rings because they allow you to look over the bases and go quickly go from magnified optics to open sights using the quick disconnect levers and return to zero feature.

Fits: Browning-High Power Bolt Action (Mauser action), Charles Daly Mauser, CIL 972C, Colt 57, H&R Pre 1973-300 & 301 & 330 & 370, Interarms-Mark X, Viscount, Mauser FN-Commercial 98, M98 Altered, Musgrave-MK III, MK IV, Parker Hale-1000, 1000C, 1100, 1200

Steel Strength.
Firearm Specific Fitment.
Designed and MADE IN USA

SPECIFICATIONS

Part Number: M902/830M
Weight: 2.0 oz
Fits: Browning-High Power Bolt Action (Mauser action), Charles Daly Mauser, CIL 972C, Colt 57, H&R Pre 1973-300 & 301 & 330 & 370, Interarms-Mark X, Viscount, Mauser FN-Commercial 98, M98 Altered, Musgrave-MK III, MK IV, Parker Hale-1000, 1000C, 1100, 1200

INSTALLATION INSTRUCTIONS

Always verify that your firearm is UN-LOADED before performing any service on it. Warne recommends that you loosely assemble rings and scope onto firearm prior to final mounting to verify eye relief and ring spacing.

Visually inspect your firearm's receiver for burrs around the screw holes and remove if necessary. Remove all oil and grease from the holes in the receiver, the base screws and contact surfaces.
Place the base(s)/rail on the receiver. In some instances the front base will overhang the receiver, place base overhang towards the rear of the firearm. Check for proper fit and alignment.
If you have short and long screws, please use the short screws in the front of base/rail, front holes of firearm.
Using a T-15 wrench (supplied with WARNE rings) loosely install the supplied Torx 15 screws.
If base(s)/rail fit properly, firmly tighten screws.
WARNE recommends no more than *25 in/lb maximum torque. WARNE recommends the use of a REMOVABLE thread locking compound on base/rail installations only, for best results.

IMPORTANT: NEVER OVER TIGHTEN ANY BASE OR RING SCREW. NEVER ATTACH A SCOPE IF THE OBJECTIVE TOUCHES THE BARREL OR CAUSES INTERFERENCE WITH THE BOLT, SAFETY OR CYCLING OF THE ACTION. ALWAYS FOLLOW THE FIREARM OR SCOPE MANUFACTURERS’ RECOMMENDED TORQUE SPECIFICATIONS. YOU ARE RESPONSIBLE FOR YOUR OWN GUNSMITHING METHODS.

If you are unsure or do not have the proper tools, please contact a gunsmith for assistance, Warne will not be held liable for stripped/damaged receivers or scopes.

M902/830M Mauser FN, Matte

Q & A